Stop rot in Glulam Beams

Repair rotted Glulam sections

Glue Laminated Timber Preservation and Repair

Property Repair Systems - Free Advice - 01626 331351 - Real People answer in plain English

 

 

 

 

     

 

Stopping Rot in Glulam Beams

Glulam Beams and Laminated Timber Beams are frequently found to be decaying due to Wet Rot. It is caused by water ingress or Condensation, both in exterior Glulam Beam bearing ends (usually inside steel shoes) or indoors, due to high humidity (swimming pools) or water leaks. Metal brackets and bolts add to the problems, due to chemical attack between the wood and the metal.

We can stop this type of decay easily using proven Boron technology, commonly applied to Electricity Supply Poles and Railway Sleepers;

1. Insert Solid Sticks - Boron Ultra Rods - these dissolve for up to 3 - 5 years, giving a long term reservoir of the active Borate

2. Inject a Stiff Paste - Boron Ultra 78 - this dissolves more immediately, giving rapid protection

3. Apply a Gel to Fixings - Boron Ultra Gel - this lubricates bolts and screws and reduces chemical reactions between wood and metal

4. Isolate the Timber - Epoxy Structural Fillers - fill between bolts, plates and concrete, to avoid damaging water from entering the wood

5. Replace in Resin - Epoxy Cast Repairs - completely replace vulnerable sections in solid Structural Epoxy Resin

6. Redesign Drainage - re-route rainwater to prevent pooling and reset gutters and downpipes away from Glulam surfaces

Glulam beam rot - in a gymnasium

Glulam Rot in a Gym, due to high humidity


Methods

1. Rods and Injection - via 10mm diameter holes drilled at 120mm along the grain, 75mm across the grain

2. Gels - to all bolt holes, plate mounting areas, on all screws and nails, to all exposed end grain

3. Resins - to line all holes, plate mountings and metal 'feet' and 'shoes'

4. Repair Sections - to replace badly damaged sections


Products

1. Boron Ultra Rods - 8mm or 12mm diameter, various lengths, in packs of 10, plastic plugs to suit.

2. Boron Ultra 78 Paste - injected into the same holes, 400cc cartridge with 8mm diameter extension tube

3. Boron Ultra Gel - brushed onto fixings and end grain, in 500cc, 1 litre and 2 litre pots.

4. Mouldable Epoxy Putty - sandable, paintable. In 1 litre pots.

5. Timberbuild Laminate Filler - fine surface crack and glue line filler. In 380cc twin cartridges. Sandable and paintable.

6. Structural Epoxy pouring and injection resins - in pouring and injection grades from 400cc to 7.5 litres.

7. Timber-Resin Splice kits - made to measure, matching laminations and timber species, colour and grain.


Repairing Glulam Beam Sections

We offer an extensive range of Timber repair options for all types of buildings, including Churches, Sports Halls, Swimming Pools and Industrial Buildings, in order to avoid removal of structural timber beams

Glulam beam rot outdoors - Pzza HutGlulam beams in A frames - hidden rot.

Glulam Rot in Structural Frames - Pizza Hut, Peterborough - due to weathering, leaking downpipes and gutters.


In many cases timbers can be repaired in-situ, from inside the building.

Timber-Resin Splice Repair Sections - new pieces of kiln dried, Strength Graded timber made to fit the damaged area, bonded in with epoxy

Timber Resin Splice Beam ready to fit

Timber-Resin Splice new Glulam Section ready for installation.

Cast In-situ Resins - Structural Epoxy Pouring resin and Injection Resins for rebuilding sections, using 'shuttering', where there is no access for a repair section to be introduced.

Boron Treatments - kill Dry Rot, Wet Rot and Woodworm inside the existing timber with Boron-based preservatives. Liquids, pastes, gels and solid rods of Borate all contribute to a long service life for damp timbers


Free Advice

Speak directly to a real person about your Glulam Preservation needs: 01626 331351


I Timber Paint I Wall and Ceiling Paint I Clear Varnishes I Top Coats I Fire Doors I Uses I

I Steel Paint I Over Coating Old Paint I Loft Conversion I Colour Charts I Home Page I

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

How to contact us

 

Property Repair Systems, Unit 3 Olympus Business Park, Kingsteignton Road,

Newton Abbot, Devon TQ12 2SN

Tel:01626 331351 Fax: 01626 331143

E Mail:help@propertyrepairsystems.co.uk

 


Our Other Sites - Index

www.boron.org.uk - Boron based products for woodworm and rots

www.dampness-info.co.uk - Rising Damp, Penetrating Damp, Hydrostatic Damp, Mold

www.deck-treatment.co.uk - deck treatments, patio treatments, Yacht deck treatments

www.drywallandfloor.co.uk - floor and wall Membranes, Cellar & Basement damp proofing

www.epoxy-info.co.uk - epoxy resins, polyester resins, polyurethane resins

www.joist-repair.co.uk - joist end repair plates, Bower Beams, joist splice plates

www.timber.org.uk - Timber-Resin Splice Technical Site

www.timber-repair.co.uk - timber repair with resins and bars

www.woodworm-info.co.uk - treat woodworm with Boron based liquid, gel and paste


Our Shopping Pages Index

FIRE PAINTS SHOP - fire retardant and intumescent paints

DAMP SHOP - damp proofing and replastering

BORON TREATMENTS SHOP - woodworm, Dry Rot and Wet Rot

EPOXY REPAIR RESINS SHOP - resins for repairing buildings

JOIST REPAIR KITS SHOP - metal plates for repairing joists

MEMBRANE FOR DAMP WALLS & FLOORS SHOP - air gap membranes

MOLD SHOP - treat black mould, paint additives

TANKING SHOP - waterproof walls

TIMBER REPAIR SHOP - repair rotted structural timbers

WOODWORM TREATMENT SHOP - kill woodworm, Death Watch Beetle

INFECTION CONTROL SHOP - hand gel, anti virus, anti-flu and anti-bacterial

SPECIAL OFFERS SHOP - current discount offers